Wattage: Every electric lighting fixture is rated for the maximum wattage of the incandescent light bulb or bulbs that you can safely use in it. Most recessed fixtures are rated for 75 or 100-watt bulbs, but some are rated for bulbs up to 150 watts.

Moreover, how do you determine how many recessed lights you need?

Whatever new recessed lighting you add should work with your existing fixtures. Measure your room to see how many fixtures you will need. A common rule of thumb is that you use one recessed light for every 4 to 6 square feet of ceiling space.

Additionally, how many can lights on a 15 amp circuit? You can put up to 30 lights (based on 50 watt light) on a 15 amp breaker.

Also, can I use a 60 watt bulb in a 40 watt lamp?

If you use a plastic socket and a traditional bulb larger than 60w the chance for heat to be created and melt the socket causing fire was very real. The heat created should not be enough to heat up the socket. I would say yes, it is OK to replace the 40w bulb with a 60w bulb using only 11w.

How bright should kitchen lights be?

- Kitchen Kitchen lights should be bright because you are working with knives and other cooking materials. For dark kitchens and more opaque fixtures, try 100 watts. If you get a lot of natural light, try using a slightly dimmer 80 watt bulb.

How many can lights for a 12x12 room?

The typical rule-of-thumb is 24" from each wall, and then 3-5 feet between cans. So in a 12' room you'd probably want two rows of lights. Considering it is a bedroom and you don't need it as bright as a kitchen, you can probably get away with 2 rows of 4 lights for a total of 8.

How many recessed lights can be on a circuit?

The main limitation to the number of recessed fixtures you can run at the same time is the rating of the circuit breaker that controls the circuit. Each fixture with a 60-watt incandescent or halogen bulb draws about 1/2 amp, so a 15-amp breaker for a standard lighting circuit would be able to handle 30 of them.

Should I use 4 inch or 6 inch recessed lights?

Size and Layering Size recommendations say to place 4-inch lamps 4 feet apart and 6-inch lamps 6 feet apart. However, these are general guidelines. Smaller task or accent lighting using 2-inch or 3-inch lamps can work in conjunction with well-placed general recessed lighting.

Can you have too many recessed lights?

In fact, using too many recessed light may leave areas of your room dark and may even cost you more on your electric bill. An expert can help you plan for the right number of lights based on the size of the space and the technical aspects of the light fixtures in question.

How far apart should 4 inch recessed lights be?

4 feet

How far apart do you put LED downlights?

Generally when installing LED downlights, it is recommended to install lights 1m from the walls and space the lights between 1.2m and 1.5m apart. Positioning can alter depending on the amount of light required and the design of the room, which should be taken into consideration when planning lighting positioning.

How far away from the wall should recessed lighting be?

If you plan to illuminate an entire wall or accent particular architectural features or pieces of art, the rule of thumb is to place your recessed light fixtures between 1.5 feet and 3 feet from the wall. If your fixtures are fixed, they should be placed a bit closer to the wall.

How many lights do I need per square foot?

For the average space of 250 square feet, you'll need roughly 5,000 lumens as your primary light source (20 lumens x 250 square feet). In your dining room, you'll want about 30 lumens per square foot on your dining table (to see, not examine, food), so if your table is 6 x 3 feet, that's 540 lumens.

What happens if you put a higher watt bulb in a lamp?

Using a light bulb with too high of wattage can lead to overheating of the light bulb. This heat can melt the light socket as well as the insulation of the wires. Once that happens, you put yourself at risk of arc faults, and this is something that could even lead to property fires.

What happens if you put a lower watt bulb in a lamp?

A 100-watt bulb will draw more power through the wires than they safely can handle. (It is okay, however, to put a bulb with lower wattage in that fixture—drawing less than the wire's maximum load isn't a problem.) Some specialty lamps or other fixtures may have even lower watt ratings for other safety reasons.

Are flickering LED lights dangerous?

Light dimmers with incompatible lightbulbs (such as LEDs) can flicker when they're set on low. Fortunately, this is not a dangerous situation either, however annoying it may be. “The only solution is to try a different type or brand of LED light, or change the dimmer itself,” suggests Orr.

Does it matter what wattage bulb you use?

When it comes to how much light you get from a light bulb, watts don't matter. Light isn't measured in watts. It's measured in foot-candles or lumens.

Which is brighter 40w or 60w bulb?

for series connection current is same. And resistance of 40w is higher than 60w means power dissipation is higher in 40w. Hence 40w bulb will glow brighter. For parallel connection voltage is same then power dissipation is higher in 60w means 60w bulb will glow brighter.

How do you know what wattage bulb to use?

2. Determine much light you need
  1. If you used to buy 100 watt bulbs, look for a bulb with 1600 lumens.
  2. If you used to buy 75 watt bulbs, look for a bulb with 1100 lumens.
  3. If you used to buy 60 watt bulbs, look for a bulb with 800 lumens.
  4. If you used to buy 40 watt bulbs, look for a bulb with 450 lumens.

What happens if you put a 100w bulb in a 60w socket?

Putting a 100-watt bulb in a 60-watt fixture could cause intense heat, melting the light socket and the insulation on the fixture's wires. Any time you have that kind of damage on wires, you're at a big risk for arc faults, where an electrical current falls off its intended path— a leading cause of home fires.

What is a 60 watt bulb in LED?

LED Light Bulbs - 60 Watt Equal. This description is included because although these bulbs typically consume between just 8 and 13 watts of energy, they produce as much light as a 60-watt incandescent bulb.

Can you put a 100w LED in a 60w socket?

One question that often comes up is this: “Can I use an LED with a higher wattage equivalent than the bulb I am replacing, such as a 100-Watt equal LED bulb in a 60-Watt rated socket, to get more light from my fixture?” The short answer is yes—as long as it still consumes fewer watts than the fixture is rated for.