To start the icemaker, lower the feeler arm to the ON (down) position. To turn off the icemaker, raise the feeler arm to the STOP (up) position.

Similarly, how do I reset my GE ice maker?

How to Reset the Ice Maker on a GE Side by Side Refrigerator

  1. Locate the shut-off switch on the front of the GE refrigerator ice maker and turn the switch off, leaving it off for at least 30 seconds.
  2. Turn the switch back on and locate the feeler arm on the ice maker.
  3. Push the feeler arm up three times quickly to reset the ice maker.

Also Know, why doesn't my GE refrigerator make ice? If the water inlet valve is defective, or if it has insufficient pressure, it won't allow water to flow through. As a result, the ice maker won't make ice. If the water inlet valve has sufficient pressure and is getting power, but the ice maker won't fill with water to make ice, replace the water inlet valve.

Also to know, why is my GE ice maker not making ice?

If your icemaker is not producing any ice: The icemaker must reach 16 degrees F before a cycle will begin. If the temperature in the freezer is too warm, ice cubes will take longer to form or may not form at all. Try adjusting the freezer temperature.

How do I reset my ice maker?

Look for the Reset Button Once you do that, you should see the bright red reset button on the bottom of the ice maker itself. To reset the ice maker, push this button in and hold it for 10 seconds. You can release it sooner if: The ice maker starts making noise and operating.

Does a GE refrigerator have a reset button?

Reset buttons typically help restore functionality to electronics or appliances in the event of a minor fault. General Electric (GE) refrigerators do not have a dedicated reset button, but you can, however, reset your refrigerator in the event of a technical problem.

How long does it take for an ice maker to start working?

6 to 12 hours

How long does it take for a GE refrigerator to make ice?

If just installed, the icemaker itself could take 24 hours to get cold enough to produce ice. The icemaker must reach 15 degrees F before a cycle will begin. The recommended fresh food temperature is 37 degrees F; the freezer temperature is 0 degrees F.

How does the ice maker work on a GE refrigerator?

Fill: A switch opens a solenoid water valve and lets in just enough water to fill the ice mold. Freezing cycle: The icemaker has a built-in thermostat which monitors the temperature level of the water in the molds. After the cubes are ejected, the arm drops down again (or pushes out) to sense the ice.

Should you turn off your ice maker?

You may also want to turn off your ice maker if you are going to be away from home for a week or more. There is no need to keep making ice if you aren't going to be using it while it is fresh before it absorbs odors and off-flavors.

How do I turn on the ice maker in my freezer?

Lower the feeler arm (metal rod) to turn the icemaker on. Toggle Switch: Flip the switch down to turn the icemaker off. Flip the switch up to turn the icemaker on - a green light will come on.

Why is my icemaker not working?

If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.

How long does it take a GE ice maker to cycle?

On a new installation, the icemaker will not start immediately after being plugged in, since the icemaker must reach a temperature of approximately 15 degrees F. before a cycle is initiated. Please allow up to 24 hours for the icemaker to begin cycling. See also New Icemaker Not Producing Ice.

How do you troubleshoot an ice maker?

Ice Maker Troubleshooting Guide
  1. Check the shutoff arm.
  2. Check the supply valve.
  3. Inspect the water supply line.
  4. Test the shutoff switch.
  5. Check the freezer temperature.
  6. Inspect the ejector gear.
  7. Test the ejector motor.
  8. Test the ice mold heater.

How long does it take a GE ice maker to make ice?

If the icemaker was installed but the water line was not added until later, once the water and icemaker is turned on the icemaker will cycle within a few minutes and fill and process its first cubes in about 1 1/2 hrs. The icemaker is dependant upon the temperature in the freezer.

Do all French door refrigerators have ice maker problems?

Many French-door refrigerators come with a through-the-door ice and water dispenser. But icemakers are a common failure point on refrigerators, so models with an ice dispenser tend to be more repair-prone than those without it.

Can water filter cause ice maker not to work?

However, the issue may be connected. In some refrigerator models, the water line that supplies the ice maker and water dispenser connect through the same water filter. If the filter is clogged, water can't get through to create ice.

What does resetting ice maker do?

Reset the Icemaker This bar, which functions like the float in a toilet tank, disables the fill cycle when the bin is full. If you see this bar pushed up against the bottom of the icemaker, but the tray isn't full, the bar is probably stuck. Pull it down to release it, and the icemaker should start working again.

How do I know if my ice maker is bad?

If the ice maker makes cubes and kicks them into the bucket – the water inlet valve is bad. If there are no new cubes in the bucket – the ice maker is bad.

How do I unclog my ice maker water line?

  1. Shut off the water valve that feeds that water-dispenser and ice-maker lines.
  2. Remove the ice bin and dump the ice out in the sink.
  3. Pour 3 to 4 cups of white distilled vinegar into the ice-maker and dispenser lines with a small funnel and allow it to soak for five to 10 minutes to break down the lime.

Can you manually fill ice maker?

Just fill a tray with water, stick it in the freezer, wait 30 minutes or so and, bam, ice! Whether you do it manually, or rely on the convenience of an automatic ice maker in your refrigerator, the process is pretty much the same. Except when it's not.

How do you troubleshoot a GE refrigerator?

How to Troubleshoot GE Refrigerators
  1. Check the settings of your GE refrigerator if it will not operate.
  2. Make sure that the refrigerator is receiving power.
  3. If the ice maker or water dispenser are not working, determine if the water supply is properly hooked up.
  4. Clean the gaskets of the fridge if the door does not open and close properly.