1. Start at the front edge of the porch and lay your floorboards out one row at a time.
  2. Attach treated decking with treated deck screws 1½ inch long.
  3. Attach tongue-and-groove with finish nails through the face of the floor boards into the batten.
  4. Trim the last board along the house to fit the width of the remaining gap.

In respect to this, what can I cover a concrete porch with?

Interlocking tiles are one of the easiest ways to cover a concrete porch, so even inexperienced do-it-yourselfers can tackle the project. The tiles are available in a variety of styles and materials, including stone, wood and composite materials.

Also Know, how do you attach wood to concrete without drilling? Here is a very easy method for attaching that wood to concrete without using all those concrete anchors. You will need a hammer drill, 20 ounce hammer and some 16d nails. Insert a 1/4" masonry drill bit, 4 or 6 inches long, into the hammer drill. Drill through the wood and into the concrete.

In this way, can you build a wood deck over a concrete porch?

Introduction: Building a Wooden Deck Over a Concrete One The obvious solution, to us, was to replace it with a wooden one. Wood is by far warmer and better looking than concrete, and if you maintain it properly it can easily last a couple of decades before you need to start replacing a piece here or there.

How do you pour concrete over existing steps?

Overpouring Old Concrete with New Concrete

  1. Step 1: Clean the surface thoroughly.
  2. Step 2: Dig a 6" wide trench around the surface on all sides to create room for 2*4 forms.
  3. Step 3: Stake 2*4 forms flush against the sides of the concrete slabs, 1" to 2" above the concrete surface (make sure height is even).

How do you paint concrete porch steps?

How to Paint Concrete Steps
  1. Prepare the concrete steps for paint.
  2. Strip off and clean any existing paint, dirt, rust or grease from the concrete.
  3. Tape off porch or wall areas that adjoin the concrete steps.
  4. Apply a coat of concrete or masonry primer to the steps.
  5. Choose a slip-proof cement paint or masonry paint.

What kind of paint do you use on a concrete porch?

Coat all areas of bare concrete with a suitable primer, such as Behr Concrete & Masonry Bonding Primer. That needs to cure at least eight hours. Then you can paint with a product designed for exterior concrete, such as Behr Premium Plus Porch & Patio Floor Paint.

What can you do with a concrete porch?

  1. Build a stamped concrete patio.
  2. Fake the look of stone.
  3. Get creative with paint.
  4. Install clay pavers for your patio.
  5. Stain or seal the concrete.
  6. Curate an outdoor living room for entertaining.

How do you build a deck over uneven concrete?

Concrete actually supports the more attractive wooden surface.
  1. Measure and construct the garden deck's frame.
  2. Lay the deck frame over the uneven concrete surface.
  3. Measure the height of each temporary support structure when the deck frame is level.
  4. Nail the deck frame onto the support beams.

Can you put composite decking directly on concrete?

Fiberon decking works with minimal clearance requirements When used with a sleeper system, Fiberon composite decking is approved for installation with 1 ½” of clearance from the bottom of the deck board to the pad/concrete surface – meaning you can now install Fiberon deck boards almost anywhere.

What is a floating deck?

Floating decks are so called because, rather than being attached to a building as are standard decks, they simply "float" on top of the ground. They are also called freestanding decks, for the same reason. But it's best to support the deck on concrete blocks.

Can you pour concrete over concrete?

If the existing concrete is in good shape structurally, you can pour new concrete over it to freshen it up. Proper prep work is key to success when layering new concrete over old. If the existing concrete is in good shape structurally, you can pour new concrete over it to freshen it up.

How do you build an elevated deck?

forming tubes
  1. Step 1: Lay Out Footings and Attach the Ledger Board.
  2. Step 2: Dig Holes for Footings and Set in Concrete.
  3. Step 3: Plumb and Brace the Posts.
  4. Step 4: Build Beams on Top of Posts.
  5. Step 5: Install the Joists.
  6. Step 6: Install the Decking.
  7. Step 7: Locate Footings for Stair Landings and Set in Concrete.